Campbell-scientific SDM-CVO4 4-Channel Current/Voltage Output Module Manual do Utilizador

SDM-CVO4 4-ChannelCurrent/Voltage Output ModuleRevision: 7/11Copyright © 2001-2011Campbell Scientific, Inc.

SDM-CVO4 4-Channel Current/Voltage Output Module You cannot reliably insert more than one solid-core wire into one terminal connector unless the wires

SDM-CVO4 4-Channel Current/Voltage Output Module or V+CVO4Remote CurrentInput V- +Id b) The SDM-CVO4 provides the voltage source to drive the loop.

SDM-CVO4 4-Channel Current/Voltage Output Module SDM-CVO4. Do not connect the screen at both ends of the cable as this may result in a ground loop bei

SDM-CVO4 4-Channel Current/Voltage Output Module Jumper shown fitted in the unconnected ‘stored’ position. Select channel(s) by fitting jumper (s) be

SDM-CVO4 4-Channel Current/Voltage Output Module TABLE 4-2. Switch Position and Addresses Switch Setting Base 4 Address 0 00 1 01 2 02 3 03 4 10 5

SDM-CVO4 4-Channel Current/Voltage Output Module Where the SDM-CVO4 is going to be used in applications where the potential difference between the dat

SDM-CVO4 4-Channel Current/Voltage Output Module is rated to withstand a 2700V, 2 second flash test, but will fail if exposed to voltages in excess of

SDM-CVO4 4-Channel Current/Voltage Output Module problem is where the sensor outputs are not within the common-mode voltage that the datalogger will a

SDM-CVO4 4-Channel Current/Voltage Output Module 6.1 CRBasic SDMCVO4 Instruction This instruction is used to control the SDM-CVO4 four channel curren

SDM-CVO4 4-Channel Current/Voltage Output Module in the device. Use of this mode takes approximately 2 milliseconds additional time per device. When

Warranty and Assistance PRODUCTS MANUFACTURED BY CAMPBELL SCIENTIFIC, INC. are warranted by Campbell Scientific, Inc. (“Campbell”) to be free from def

SDM-CVO4 4-Channel Current/Voltage Output Module Else WD_0_540 = WD_0_360 EndIf ' Scale the measurements for the SDM-CVO4 to output 0-1

SDM-CVO4 4-Channel Current/Voltage Output Module location is used to scale the output to 0-10000mV for voltage mode, or 0-20 mA for current output mo

SDM-CVO4 4-Channel Current/Voltage Output Module Setting the Reps parameter to 0 (Zero) will cause the addressed SDM-CVO4 to shut down, turning off al

SDM-CVO4 4-Channel Current/Voltage Output Module ; Measure the wind direction from a potentiometer windvane 2: Excite-Delay (SE) (P4) 1: 1 Reps

SDM-CVO4 4-Channel Current/Voltage Output Module ; As we have four channels to output, we will first copy the ; current readings with P54, block move

SDM-CVO4 4-Channel Current/Voltage Output Module ; Then apply the scaling with one instruction P53 ; The readings are scaled -3000 to +5000, i.e. to ;

SDM-CVO4 4-Channel Current/Voltage Output Module ; Now update the SDM-CVO4 with the information ; for the four channels 16: SDM-AO4 (P103) 1: 4 R

SDM-CVO4 4-Channel Current/Voltage Output Module ; Wait 100 ms for it to power-on and the outputs to stabilize ; You may need to increase this delay i

SDM-CVO4 4-Channel Current/Voltage Output Module 24

SDM-CVO4 Table of Contents PDF viewers note: These page numbers refer to the printed version of this document. Use the Adobe Acrobat® bookmarks tab

Campbell Scientific Companies Campbell Scientific, Inc. (CSI) 815 West 1800 North Logan, Utah 84321 UNITED STATES www.campbellsci.com • info@campbel

SDM-CVO4 Table of Contents ii Tables 4-1. Datalogger to SDM-CVO4 Connections ... 4 4-2. Switch Position

SDM-CVO4 4-Channel Current/Voltage Output Module The SDM-CVO4 is a synchronously addressed datalogger peripheral designed to allow the datalogger to o

SDM-CVO4 4-Channel Current/Voltage Output Module The SDM-CVO4 is a synchronously addressed datalogger peripheral. The datalogger’s SDM ports are used

SDM-CVO4 4-Channel Current/Voltage Output Module Weight: 370 g EMC Status: Complies with EN55022-1:1998 and EN50082-1:1998 2.2 Output Specifications

SDM-CVO4 4-Channel Current/Voltage Output Module Maximum recommended continuous operating voltage: 240 VAC RMS differential between an output and data

SDM-CVO4 4-Channel Current/Voltage Output Module If the total cable length connecting SDM-CVO4s to SDM-CVO4s, other SDMs and the datalogger exceeds 6